Bobber Bobber Motorcycles, page #5

THIS IS A SWEET CUSTOM BOBBER WITH AN 80 CUBE EVO ENGINE SLIGHTLY WARMED OVER WITH A CAM AND A SUPER E CARB, RUNS LIKE A TOP AND RIDES GREAT! FRAME IS POWDERCOATED IN HAMMERTONE CHARCOAL AND THE TANK AND FENDER ARE WRINKLE FINISH BLACK. THIS BIKE GETS THUMBS UP AND COMMENTS EVERYWHERE IT GOES AND JUST HAS A BAD ASS COOL LOOK TO IT!

you looking at a 750cc suz,bobber custom built  it has new white wall tires it starts right up and runs and drives great it is really for the road,thanks for looking and good luck bidding,,,

Up for sale is a freshly built Kraft Tech Rigid. I purchased the bike nearly completed and did the entire build all over again ensuring everything was done the correct way with the appropriate parts. The bike has never been titled because the previous ownership never had completed it.

2015 CUSTOM BOBBER Top Line Information Year: 2015 VIN: MVIN357797IND Make: CUSTOM Stock: A1206 Model/Trim: BOBBER Condition: Pre-Owned Engine: 95 cc HARLEY DAVIDSON Exterior: Black Transmission: 6-SPEED Mileage: 500 Additional Photos* * * Click Photos to Enlarge * * * * * * Click Photos to Enlarge * * * Phone: (630)425-3237 Alt: (630)624-8303 DescriptionCUSTOM SHOVELHEAD BOBBER!!! 2015 CUSTOM BOBBER FRESH 79 SHOVELHEAD MOTOR 95CI: S&S 4 5/8 FLYWHEEL, RODS, FORGED PISTONS(9:5:1) ANDREWS C CAM MANLEY STAINLESS VALVES, HIGH LIFT SPRINGS W/ TITANIUM COLLARS SOLID LIFTERS ROWE CAST IRON GUIDES COLONY ALUMINUM PUSH RODS STEEL BREATHER GEAR MILD HEAD PORTING STEEL BREATHER GEAR REBUILT STOCK OIL PUMP CRAFTTECH SOFTAIL FRAME ULTIMA 6 SPEED TRANSMISSION HYDRAULIC CLUTCH CHROME SPOKE WHEELS SPRINGER FRONT END CUSTOM LEATHER SEAT 2 SETS OF EXHAUST   At our dealership we work very hard to accurately describe our vehicles through text descriptions and elaborate photos. When you purchase a pre-owned vehicle it is not a new vehicle.

2011 Ultima Bobber Ultima 120 motor Ultima 6 speed Ultima starter Mikuni 48 carb Springer front end Springer seat Dual disc brakes Brass forward controls 10" ape hanger bars Short heat wrapped exhausts Headwinds headlight Rear foot pegs mounted into frame ( screw in and out if you want removed ) Suction cup rear seat included 2" open belt primary Chain drive Ridewright wheels 1st. service just completed ( oil change and bike thoroughly checked over ) *** CLEAR FLORIDA TITLE  *** This bobber was built by a licensed Florida State motorcycle builder... Title make: ACYL This bobber can be registered and insured in all states and is a blast to ride...

2012 rooke style bobber 113 Midwest ultima 6 spd ultima 2" ol school belt 250 rear This bike was finished mid summer 2012 and has estimated 500 miles on it , runs and drives perfect ,  The orange chopper in the last picture could also be had for $14,000.00

This bike could be close to one of a kind. Want to turn some heads in the streets this is the bike for you. Want to enter it into a show this is the bike for you.

Custom Harley Rigid Bobber- Professionally built- Kraftech frame, 80'' Evo style motor with a mild cam,Built on S@S cases and every thing else Harley OEM parts. Super E polished carb. 5 speed tranny linked to a BDL 3'' open belt.

2006 pro street custom new ultima 107ci motor with 500 miles. new 0pen belt ultima primary and clutch. 5 speed trans.

  HD  Bobber/Chopper For Sale- like the "Billy Bike" This Bike was built to resemble the famous "Billy Bike" ridden by Dennis Hopper in the iconic "Easy Rider" Movie from 1969.  It has been a prolific Bike show winner and is a lot of fun to drive with the low seat height and 96" stroker motor!    Frame:   Paughco-Rigid Wishbone-35 degree rake-Custom Molded and painted   Gas Tank: Paughco-3 .25 gallon custom "flame"paintjob.   Forks:  Paughco-Springer -3" over extension- 35 degree rake-pull back "drag" style bars.   Wheels: Landmark-Rear Wheel-18" for 180 tire-Ball Hub-80 Spoke "diamond cut".

I'm selling this bike for my next door neighbor, who rarely rides it since he has too many toys to play with.  I can attest to the quality of the bike and the condition and that the bike has been professionally maintained by a local shop.   Here are the specs.

Selling my custom built bobber. Hardtail with springer front. Satin black and red paint.

 THIS Bobber built for advertisment and promotion af a famous clothing company. " TRUE RELIGION SPRING 2012 - THE REBEL " Check this web site ! http://www.youtube.com/watch?v=kkXdqguDYxU AND IT IS LOUD, FAST, AND FUN TO RIDE.

Harley Davidson 103" Twin Cam Motor Baker 6 Speed RSD Transmission Rolling Thunder Frame (Heavy Duty Great Frame) ! Springer Front End- Works Awesome !     Rides Great for a Rigid with spring seat and big tire ! 300 Rear Tire Ride Wright Custom Wheels (Black w/ Gold Spokes)   No Paint !   It looks so cool like this I never took it apart to paint it !    No turn signals !

 This is a Cali Bobber, built by a reputable shop. Redemption Cycles California. Bike is 1980 750c Bobber Custom.

titled as 1999 harley davidson sportster. rigid frame DNA springer 200 rear tire 14 inch ape hangers. no paint on bike all powder coated even the tank and fenders.

THIS IS A 2016 CUSTOM BOBBER THAT I BUILT THIS YEAR FOR MYRTLE BEACH BIKE WEEK. IT IS A 240 REAR TIRE RIGID FRAME THAT IS 4 UP 2 OUT AND 38 ON THE NECK. THE FRONTEND IS A STOCK CHROME THAT IS 4" OVER AND A 5 DEGREE TREE.

Covington’s Cycle City 2008 Covington Custom Bobber 1st Titled in Texas 10/20/2014 Built by the legendary Jerry Covington! This is one of the most beautiful and detailed motorcycle I have ever seen, let alone owned. The history as best I can, and based on conversations with Jeff Covington himself is as follows: • Sold in 2011 at Daytona Bike Week to local TX collector.

Custom Build Chopper Bobber 2008 Cenzi Custom Chopper Build $38.000 in Value http://www.youtube.com/watch?v=VGT9sMVECl8   Build by Tony Cenzi in 2008 Only 700 miles perfect condition like new Engine 124 CC TP PRO SERIES Transmission Baker 6 Speed Won #1 Best Bobber 2008 All cables inside the frame (nothing on the exterior) Eye catcher Contact George 847 505 6777 By sale by owner      

2012 custom bobber has a S&S motor 88 ci completely rebuilt. 6 speed ultima tranny new and a ultima 3 in open belt primary new. New paint and new tires and new set of hooker pipes nice and loud.

2012 custom bobber S&S 88ci motor completely rebuilt from bottom to top. Ultima 6speed tranny new . Has a new ultima 3 in open belt primary .

Best Offer Available2009 Martin Brothers Custom Bobber Dream Machines of Texas - Contact Sales @ 972.380.5151 Top Line Information Year: 2009 VIN: MMWS2006MBBR31104 Make: Martin Brothers Model/Trim: Custom Bobber Condition: Pre-Owned Engine: 1340 cc V-Twin Exterior: Gold Transmission: 6-Speed Mileage: 800 Description972-380-5151 YOU ARE LOOKING AT A VERY NICE 2009 MARTIN BROTHERS CUSTOM BOBBER.  THE BIKE DOESN'T HAVE AN ODOMETER SO WE ARE SELLING THE BIKE AS NON ACTUAL MILES.  IT IS CUSTOM PAINTED BY JOE MARTIN GOLD FLAKE WITH BLUE AND PURPLE FLAMES IN COLOR AND POWERED BY A HARLEY DAVIDSON 1340CC (80") CARBURETED ENGINE AND 6 SPEED TRANSMISSION.  THE BIKE COMES WITH A MARTIN BROTHERS HANDMADE GAS TANK, OIL TANK, EXHAUST, REAR FENDER, FENDER SUPPORTS, HANDSHIFT, FOOT CLUTCH, BATTERY BOX, TOP MOTOR MOUNT/COIL COVER, AIR RIDE SEAT, TAIL LIGHT, FORK BRACE, NARROWED APEHANGER HANDLEBARS, CUSTOMIZED FRAME WITH 2" UP AND 2" OUT STRETCH, PRO ONE FORK ASSEMBLY STOCK SOFTAIL LENGTH WITH BRUSHED FINISH, BLACK BIKE WHEEL BRUSHED ALUMINUM 40 SPOKE WHEELS, 18X7 REAR, 21X2.15 FRONT, GMA BRAKES, FRONT BRAKE HAND CONTROLS, CUSTOMIZED THUNDERHEART FOOT CONTROLS WITH BRUSHED BACKING PLATES, 80" HARLEY DAVIDSON CRATE MOTOR WITH S&S VALVE TRAIN, RED SHIFT CAM, PORTED HEADS BY NATIONAL PRO STOCK AND PRO GAS DRAG RACING CHAMPION DAVE FEAZELL, S&S E CARB WITH THUNDERJET CRANE IGNITION, NOLOGY COIL, 6 SPEED OVERDRIVE TRANSMISSION, BRUSHED FINISH BDL BELT DRIVE, SPYKE STARTER, WESTBUY GAS CAP, MATT HOTCH KICKSTAND, REGINA GOLD CHAIN, PM HAND GRIPS, PBI REAR SPROCKET, AND 1 KEY.  THERE ARE NO SCRATCHES, DENTS, OR DINGS THAT I CAN FIND WITH THE EXCEPTION OF A MINOR ROCK CHIP ON THE FRAME SMALL CHIP ON THE REAR FENDER.  THE CHROME AND ALUMINUM ARE IN VERY GOOD CONDITION.  THE FRONT TIRE AND THE REAR 200MM HAVE GOOD TREAD LEFT ON THEM.   wE LOVE TRADES!!! *NATIONWIDE WARRANTY AVAILABLE!!! WORLDWIDE SHIPPING AVAILABLE!!!

Custom 2010 bobber built by Design Worx. Frame is by paucho engine is s&s generator style 93" panhead, baker 4spd trans kick start only. Frame, bars,rims and alot of parts copper plated then antiqued.

Up for sale is this beauty! Owned for approx 3yrs now, title in hand. I just don't have time to ride  due to summer being my very busy season.

I am selling my 1979 harley bobber. This is a running and driving bike that needs nothing but a rider. It is pretty good looking and there are no bikes around that look like it.

1968 Triumph Bobber Built by our machinist 3 years ago, and has less than 1,000 miles on it.Bike has a bunch of cool custom fabricated parts, including bolt-on Hardtail Section, High Pipes, Aluminum Oil Tank, Sissy Bar, Forward Controls, Handlebars, Sprocket Carrier and Caliper Carrier, etc.Rear wheel has Stainless Disc & 4-Piston Billet Caliper with GMA Master Cylinder &Stainless line.Front Wheel is Triumph two-shoe brake cleaned & rebuilt with new shoes and bearings laced to a 21" Excell rim.Tires are Avon Speedmaster front and Avon Safety Mileage rear. Motor has been completely rebuilt from the crank up. Fresh bearings,bore & pistons, valves & guides. New clutch, primary chain, etc.Ignition is Boyer.

This is a South Florida Choppers built custom Springer ridged with a Harley Davidson 1340cc EVO.  It has a new fat bob 4 gallon tank and all tins were recently powder coated satin black.  The bike only has about 1000 miles on it and runs great.  Only selling because I need the cash.  Very light weight and fast bike. I am the original owner. Buyer will pay shipping.

Beautiful Custom Bobber Bike was custom built in 2009 by Ultimate Cycles in Miami, FL. Specifications: Custom real copper springer front end. 113" Ultima engine.

 Here for your viewing is my BEAUTIFUL BSA Chopper!  This is an absolutely stunning custom built motorcycle. The engine built by legend brit bike specialist John York is from a 1968 Thunderbolt completely rebuilt, polished, and tuned to perfection!  The bike project was overseen and assembled with "Master Custom" builder Denny Berg in Southern California! The bike has snagged several awards and trophies at every show the most prestigious being "Best Rigid" honors at the Del Mar Concours!

2008 custom built bobber based on a kicker 5150 kit bike. 250cc vtwin, custom airbrushing and pin striping. Hand fabricated side air draft intake/bug eye air filter, hand fabricated horse shoe shaped faux oil tank.

No reserve on this bike. Highest bid over $14999 gets this bike. It is priced to sell.

Custom Bobber -- This is one sexy bike!! Excellent condition! NEAR NEW!

CLEAN TITLED 2004 CUSTOM ON A SANTEE FRAME. REV TECH 100 MOTOR. BIKE WAS $25000 NEW IN 2004.

This is a custom built bike, S&S lower end on the V-Twin motor, 97" axtell jugs are bored out and 10:1 pistons with a hopped up cam.  This bike moves quickly, lots of torque and well balanced.  Breaks have been gone through and stops on a dime.

Built in 2009, only about 2000 miles on it.  Runs and rides great.  The bike is very cool and gains attention where ever you take it.  Has twisted Spokes, 1340 HD EVO, Powder coated frame and tins, front and rear brakes, springer front forks, wife white walls, custom exhaust.  I will deliver it anywhere in south Florida.  Buyer must make arrangements for transportation outside of Florida.  

If your looking for an attention getter.....This is it! Custom built motorcycle Bobber style Mat Black paint unique solid chrome wheel in the rear, and wire wheel in the front. mechanically the bike is in excellent condition.

To my memory, this is the first time in years that a custom Zero Engineering bike has been listed on Ebay (and not via private sale or brokerage). I purchased this bike in 2009 and placed it in the front lobby of my family-owned company office. It lived there for 3 years as decoration, and I took it out to ride around the parking lot occasionally on the weekends, or to get it serviced.

2005 SURGICAL STEED BRONCO I NAMED "MOTO" WHICH IS AFRICAN FOR FIRE. BUILT BY JOHN COVINGTON WHO USED TO BE IN MAGAZINES ALOT AND OWNED THE ORIGINAL SURGICAL STEEDS. LOW MILES.

2009 Chopper stripped down bobber with less than 3k miles. This bike is light, fast and fun as hell to ride. Comes with: Ultima Wolfdaddy Frame Harley 80 Evo Motor CV Carb recently rebuilt with sportster needle Arlen Ness Big Sucker Ultima Open Belt Primary WCC Villan Tank LA Chopper Risers w/ Flanders Bars PM Hand Controls New All Ballz Starter Push Button Starter New front tire No turn signals, no fancy wiring, low miles and strong running Harley crate motor.

CHASSIS DESIGN COMPANY 100 IN ULTIMA MOTOR 6 SPEED TRANS 200 REAR 21 IN FRONT BIKE IS FAST AND HANDLES REALLY GOOD RUNS GREAT 3 IN BDL BIKE HAS REALLY LOW MILES BEEN GARAGED FOR YEARS  

THIS MOTORCYCLE WAS CUSTOM BUILT BY A PROFESSIONAL BUILDER AT LUCKY 7 CHOPPERS, CA. BEAUTIFUL PAINT JOB, 4K INVESTED! FEEL FREE TO STOP BY AND CHECK IT.

THIS MOTORCYCLE WAS CUSTOM BUILT BY A PROFESSIONAL BUILDER AT LUCKY 7 CHOPPERS, CA. BEAUTIFUL PAINT JOB!  FEEL FREE TO STOP BY AND CHECK IT. EVERYTHING WORKS AND RUNS PERFECTLY.

" 08 Custom Wide Tire Bobber"       Driving Rods And Rides Is Proud To Present This Sweet 2008 Custom Bobber. This Is A Super Clean Bike With Only 4,000 Miles Since Completion. This Ride Has A Nasty Powerful 110" Revtech Motor Mated With A 6 Speed Revtech Transmission And Primary.

  2006 Covington Classic Custom Bobber - 88ci Evo Motor - Chrome Springer Goose Neck Front End (cost $2000) - NEWER Avon & Dunlop Wide White Wall Tires Front & Rear (cost $400) - Classic 2-Tone Green Body w/ Yellow Pinstripe (cost $1000) - RPM Forward Controls (cost $400) - BDL 3 Open Primary (cost $1000) - Baker 5 Speed Transmission (cost $800) - Chrome Front & Rear Brake Calipers (cost $400) - Green w/ White Trim Springer Solo Seat (cost $300) - Front (21) Rear (16) 80 Spoke Wheels (cost $600) - Covington Custom Exhaust (cost $500) - Old School Grips (cost $50) - Fork Bag (cost $75) - Curved Tag Bracket (cost $150) - Bullet Turn Signals (cost $50) - Stainless Steel Brake Lines (cost $100) - The bike is in great running condition, and rides well. It has been through our service department, and has been serviced and inspected. In-House Buy Here, Pay Here Financing offered & Trades Accepted.

This is a cool bobber style bike built by Southern Motor Works in 2005 , it has only 4516 miles and its in great condition . It has a rev tech 100 , 6 speed trans ,200 mm rear ,16'' ape ,braided stainless wires and oil lines , 4'' primary belt ,also has  turn signals in front (not shown in pictures ) I took them of for the looks after inspection , its a fun bike and it runs great ,reason for selling is that Im getting a older panhead . Any questions or more detailed pics ,let me know .

This is a 2005 springer bobber. The actual name of the bike is a lil bruiser. Its made by the company Revolution.

1981 sportster custom 45 springer front endweld on hard tail

Here are the specs for this beautiful custom 2006 bobber. 1.  softail 2.  80 evo black and chrome motor 3.  screaming eagle SE3 cams 4.  adjustable push rods 5.  htcc screamining eagle heads 6.  cv carburetor 7.  ness high flow air cleaner 8.  dyna singal fire ignition high output 9.  bub 2 in 1 exhaust 10.  sucker punch sally solo seat 11.  american wire 80 spoke chrome wheels 12.  black pro one front end 13.  directionals built in to the triple trees 14.  3.5 gal. indian larry gas tank 15.  round oil tank 16.  10 in.

2002 custom bobber / chopper/softail cruiser.5500 miles- ** 80 evo engine, 5 spd rev tech tranny ( kick start ), velocity stack on carb / pipes wrapped in black pipe cloth.new oil change, ** Amazing ghosted silver flames on paint job. ** new battery, runs great, sounds great and its CHEAP! Michigan assembled title.  **cheap insurance because of what i valued it at. kicks over on the first kick.everything works.

 " 08 Custom Springer Bobber"       Driving Rods And Rides Is Proud To Present This Gorgeous 2008 Custom Springer Bobber. This Is A Super Clean Bike With Only 6,000 Miles Since Completion. This Ride Has A Built 1340 Evo Harley Davidson Motor Mated With A 6 Speed Ultima Transmission And Primary.

2006 Santee Custom 110, 2006 Clean title in hand! Santee straightleg Frame features stock stretch w/ 30 degrees of rake. Crate 96" S&S motor.

Custom 2007 Bobber. Six speed 100 inch Revtech. 6,900 miles.

I have here a suzuki s50 that I bought new in 2007 and am the origional owner of. Theese bikes make awesome bobbers! look at the internet and you will see great examples.

2008 Proper Chopper Bobber 357 ST Our goal is to satisfy our customers. We stand behind every unit we sell.Top Line Information Year: 2008 VIN: 1P9S229568C522273 Make: Proper Chopper Stock: P04117 Model/Trim: Bobber 357 ST Condition: Pre-Owned Engine: 1753 cc Exterior: Black Transmission: 6 Speed Mileage: 7,326 VideoAdditional Photos* * * Click Photos to Enlarge * * * * * * Click Photos to Enlarge * * * Contact Steve Hollander Toll Free: 877-470-6111 Phone: (520) 747-8339 Description Looking for a Head Turning Motorcycle, that will Stand out from the Crowd, Then take a look at this Awesome, 2008 Proper Chopper 357 ST!! This Beauty is One of a Kind!!

 Exile fatbob harley night train Real exile bike brand new build using a Harley 2001 Night train. has a Harley title so no issue on registering. Brand new bike has less than 700 miles on it since new build.

I have up for sale a 1994 sportster I chopped awhile back.It doesn't have the standard sporty hardtail you can purchase for it.I grafted a OIF Triumph hardtail onto it to give it a very narrow profile.I built a good deal of parts for this bike including the nacelle,exhaust,handlebars,etc.the bike also has two 19'' wheels with new tires(less than 200 miles on them).The top end was rebuilt at a Harley-Davidson dealership with new jugs pistons and pushrod tubes.The bike is very dependable as i have rode it on multiple trips with no issues and rode it back and forth from work as a daily driver.The only thing is it leaks a little.And has signs of typical wear for a bike that is ridden.I have a clear florida title in hand.Thanks for looking. Parts list: David bird OIF Triumph hardtail,19'' 9 spoke mags,Michelin commander II's,Crane cams HI-4 ingnition module,H-D black LED light,Chain conversion,Redtail leather seat,powdercoated parts.Not a huge parts list,I tried to keep the bike as simple as possible.It only got what it needs to shoot down the road. I built this bike in my garage,I enjoyed building it and have enjoyed riding it even more.I have a slew of projects so im selling to fund my other toys.If your interested place a bid.

 This Custom Bobber I am listing for a friend. He is building a couple motorcycles and needs some extra cash to finish them. This is one awesome motorcycle with an awesome paint job.  It's a 2000 Harley Davidson Sportster 883 with a 1200 kit installed.

CUSTOM BOBBER This is the latest build at FLYINEYEBOBBERS . Custom metalflake paint 12 inch apehangers Diamond tuck solo seat Hardtail Low & Loud Custom wrapped pipes Side mounted tail light   Call 336-469-2188

 For auction a Buell prostreet bobber set in a Atlas type  softail frame buel 1203 m-2 engine w/ thunderstorm heads documented 10 k at install -2011 andrews n-4 cams added-2011 Ultima single fire ignition-2011 Supertrapp exhaust-2011 Dna  springer front end-2011 k&n intake-2011 40 degree rake Bike rides/handles extremely well with no known issues and yes the trail is correct for the rake (because somebody will ask thinking they're the only ones  on top of this sort of stuff)